- How do you start a pool for the first time?
- Can you put too much chlorine in a pool?
- How many bags of shock do I need to open my pool?
- Should I shock my pool when I first fill it up?
- Is shock the same as chlorine?
- Is it OK to fill a pool overnight?
- What to do when you first fill your pool?
- How do you treat a brand new pool?
- What chemicals do I need to start my pool?
- What chemicals are needed to open above ground pool?
- Do I use shock or algaecide first?
How do you start a pool for the first time?
Follow these steps for opening your pool for the first time….Steps to Open your Swimming PoolTurn on your filter system.
Using test strips, test the swimming pool’s water total Alkalinity Levels (adjust if necessary).
Using test strips, test the swimming pool’s water PH Level (adjust if necessary).More items….
Can you put too much chlorine in a pool?
Having too much chlorine in your pool water can be dangerous. Exposure to high levels of chlorine can cause lung irritation, skin and eye damage, and provoke asthma. … High chlorine levels decrease the pH of your pool’s water, making it more acidic.
How many bags of shock do I need to open my pool?
To shock your pool, use 2 pounds of shock for every 10,000 gallons of water, which should raise your chlorine to 10.0 ppm. Depending on your pool, you can use Leslie’s Power Powder Plus or Leslie’s Chlor Brite. After shocking the pool, run the circulation system for at least 2 hours before adding an algaecide.
Should I shock my pool when I first fill it up?
The first couple of weeks after starting up your pool is the time to make sure everything is running right. You will need to check your water readings more often in the beginning. … At first you’ll add chlorine in what’s called “shock” levels – an extra heavy dose to start your pool off.
Is shock the same as chlorine?
Shock is chlorine, in a high dose, meant to shock your pool and raise the chlorine level quickly. … Chlorine tabs (placed in a chlorinator, floater, or skimmer basket) maintain a chlorine residual in the water. You do need to use both tabs and shock.
Is it OK to fill a pool overnight?
Hi, with 12″ of water in the pool you should be fine to let it fill all night. The stretching should be done and the liner tight against the wall. If so, let it go. There is some air gap between the liner and the wall in a few areas.
What to do when you first fill your pool?
What Do You Do After an Above Ground Pool Is Filled With Water?Step 1: Learn about how to prevent drowning and pool chemical injuries. … Step 2: Turn on the filter. … Step 3: Vacuum and skim off debris. … Step 4: Test the water, and then test it again. … Step 5: Enjoy your pool, but safely!
How do you treat a brand new pool?
Steps:Turn on the pool pump and filtration system. … Test the pool water for pH, chlorine and total alkalinity. … Adjust the pH until it is between 6.8 and 7.2. … Add a sequestering agent according to package directions. … Allow two days for the pool balance to settle.More items…•
What chemicals do I need to start my pool?
The Perfect Chemical Balance for a Pool Start UppH – 7.2-7.6.Alkalinity – 80-120 ppm.Calcium Hardness – 180-220 ppm.Cyanuric Acid – 30-50 ppm.Chlorine – 1-3 ppm.
What chemicals are needed to open above ground pool?
How To Open Your Above Ground PoolPool Shock.Pool Algaecide.Chlorine Stabilizer.Alkalinity Increaser & Decreaser.
Do I use shock or algaecide first?
While shocking and adding algaecide is effective in getting rid of algae, it should not be done together. This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM.